Antenna Cable Comparison for Aircraft Avionics – Gulf Coast Avionics Skip to content
Previous article
Now Reading:
Antenna Cable Comparison for Aircraft Avionics
Next article

Antenna Cable Comparison for Aircraft Avionics

A weak radio transmission, intermittent GPS position, or poor transponder performance does not always begin at the avionics box or antenna. The coaxial cable assembly between them is part of the RF system. This antenna cable comparison focuses on the decisions that matter in aircraft: impedance, frequency, signal loss, shielding, connector quality, routing, and the installation requirements that govern a particular system.

For an aircraft upgrade, cable selection should never be based on outside diameter or price alone. A cable that works acceptably for a short VHF COM run may create unnecessary loss in a longer transponder, DME, or GPS installation. Just as important, an otherwise correct cable can become a problem when it is sharply bent, poorly terminated, routed beside high-current wiring, or substituted for an approved assembly.

Antenna Cable Comparison: Start With the System

Most aircraft communications, navigation, surveillance, and GPS antenna systems use 50-ohm coaxial cable. That includes typical VHF COM, NAV, GPS, transponder, ADS-B, DME, and ELT applications. The cable, connectors, and antenna must maintain the impedance specified by the equipment manufacturer. A 75-ohm cable intended for television or video work is not an appropriate substitute in a 50-ohm avionics antenna circuit.

The type of signal also changes the cable decision. VHF COM and NAV systems operate at lower frequencies than transponders and ADS-B equipment. Higher-frequency signals experience more attenuation for a given cable length, so cable loss becomes more consequential as frequency and run length increase. A short run to a belly-mounted transponder antenna may allow several suitable cable choices. A long run from a panel-mounted transponder to a tail-mounted antenna demands closer attention to published attenuation figures and installation guidance.

GPS deserves separate consideration. Many GPS antennas are active antennas that receive power through the coax center conductor. The antenna cable must meet the manufacturer’s requirements for impedance, maximum loss, connector type, and length. Adding adapters, using damaged connectors, or exceeding the approved cable loss can prevent the antenna from receiving adequate power or reduce receiver sensitivity.

ELT installations are another case where substitution can be risky. The ELT manufacturer’s installation manual may specify a particular cable type, length range, connector, or approved antenna assembly. Because the ELT is emergency equipment, follow the current approved data rather than applying a general coax rule.

Common Coax Types Used in Aircraft

RG-58: Compact but Not Always the Best Choice

RG-58 is a 50-ohm coaxial cable that has been widely used in radio applications. Its relatively small diameter and flexibility can make it convenient in tight areas. However, it has higher attenuation than many modern aviation-preferred alternatives, particularly as frequency and cable length increase.

For certain short, low-frequency VHF applications, RG-58 may be acceptable if the equipment documentation permits it. It is less attractive for longer transponder, ADS-B, DME, or GPS antenna runs, where lower-loss cable can provide more margin. Not every RG-58 product is built for aircraft use, either. Material construction, temperature rating, shielding, and jacket characteristics matter as much as the designation printed on the cable.

RG-400: A Common Aviation Standard

RG-400 is often the practical choice for general aviation coax installations. It is a 50-ohm, double-shielded cable with a durable fluoropolymer jacket and silver-plated conductors. It offers substantially better high-frequency performance than RG-58 while remaining flexible enough for many aircraft routing paths.

Its double shielding helps limit RF leakage and susceptibility to interference in crowded avionics bays. RG-400 is frequently selected for COM, NAV, GPS, transponder, ADS-B, and other avionics antenna applications when it meets the equipment manufacturer’s instructions. The trade-off is cost and a somewhat larger, less forgiving cable than RG-58. Those trade-offs are usually justified when reliability and long-term serviceability are the priority.

RG-142: Similar Electrical Purpose, Different Handling

RG-142 is also a 50-ohm, double-shielded coax commonly encountered in aviation and RF work. Electrically, it can be suitable for many of the same applications as RG-400, depending on the specific cable construction and approved installation data. Its jacket and handling characteristics differ, however, so it is not automatically interchangeable from an installation standpoint.

Where vibration, heat, routing constraints, or connector compatibility are concerns, compare the cable datasheet and the avionics manufacturer’s requirements rather than selecting solely by attenuation. A cable that performs well electrically still must survive the environment where it is installed.

Larger Low-Loss Cable: Use It Where the Installation Supports It

Larger 50-ohm coax types can reduce attenuation further, which can be beneficial on unusually long runs or at higher frequencies. The gain in RF performance comes with installation penalties: larger bend radius, added weight, more difficult routing, and connector limitations. In a small aircraft, a lower-loss cable is not automatically a better installation if it cannot be routed without tight bends or strain at the antenna and radio connections.

For most standard general aviation avionics upgrades, RG-400 or another manufacturer-approved aviation-grade 50-ohm cable offers a sensible balance of loss, shielding, durability, and installation practicality. Special cases should be evaluated as part of the complete antenna system.

Loss Matters More Than It Looks

Coax attenuation is measured in decibels per length at a stated frequency. Even modest loss reduces the power arriving at the antenna during transmission and reduces weak-signal performance on receive. At transponder and ADS-B frequencies near 1 GHz, loss rises much faster than it does in the VHF COM band.

That does not mean every antenna lead must be oversized. It means the run should be as short as practical, with the correct cable and as few connection points as possible. A direct, properly terminated cable run is preferable to a longer run with unnecessary adapters, barrel connectors, and repair splices.

When comparing published cable data, use attenuation values at the frequency that matches the system. Comparing cables only at a low reference frequency can lead to the wrong choice for a 978 MHz UAT or 1090 MHz transponder installation. Also consider the total installation loss, including connectors and any approved couplers, not only the cable itself.

Connectors Are Part of the Cable Assembly

A premium coax cable with an improperly installed connector is still a poor antenna lead. BNC connectors are common in aircraft avionics installations, while TNC, SMA, and other connector styles may be used on specific GPS, portable, or modern equipment interfaces. Connector type is determined by the equipment and antenna, not personal preference.

Crimping and stripping dimensions must match the exact cable and connector family. A connector designed for RG-58 may not correctly fit RG-400, even when both are 50-ohm cable. Incorrect tooling, an exposed braid strand, insufficient center-pin retention, or excessive heat during soldering can produce intermittent faults that are difficult to locate once the panel is closed.

Use aviation-quality connectors from known manufacturers and inspect every termination. The center conductor should be secure, the braid should be properly captured, and there should be no visible damage, loose strands, contamination, or strain on the connector. A continuity and insulation check is valuable, but it does not replace an RF performance check when troubleshooting a suspected antenna system problem.

Routing, Support, and Bend Radius

Aircraft cable routing has to protect both the coax and the rest of the electrical system. Keep antenna coax away from high-current alternator, starter, strobe, and ignition wiring where practical. Cross unavoidable electrical runs at right angles instead of bundling them together for long distances. Follow applicable installation data and aircraft-specific practices for separation, clamping, and protection.

Avoid sharp bends, pinched sections, and unsupported cable runs. Every coax type has a minimum bend radius. Exceeding it can deform the dielectric, change impedance, and raise signal loss without leaving an obvious external defect. Leave enough service loop for maintenance, but do not coil excess cable tightly. A large, controlled service loop is preferable to a compact coil behind the instrument panel.

Protect cable where it passes through bulkheads, ribs, or other structure. Use appropriate grommets, chafe protection, and cushioned support. Antenna-end connections deserve particular attention because they are exposed to vibration, moisture, temperature changes, and physical stress during inspections and maintenance.

Use the Installation Manual as the Final Authority

This antenna cable comparison can narrow the options, but the installation manual for the specific radio, transponder, GPS navigator, ELT, and antenna controls the final selection. Manufacturer instructions may define approved cable types, maximum cable loss, antenna location, connector torque, grounding requirements, and test procedures. STC data, aircraft maintenance documentation, and applicable FAA regulations may add further requirements.

For certified aircraft, a cable change can affect approved installation data and return-to-service requirements. For experimental and kit aircraft, builders have greater responsibility to make sound system decisions and document the installation clearly for future maintenance. In either case, treating the antenna lead as a critical avionics component prevents avoidable performance problems.

Before ordering cable or beginning an installation, identify the exact avionics model, antenna model, planned cable length, routing path, and connector requirements. Gulf Coast Avionics can help match those details to the correct equipment and installation approach, so the cable assembly supports the performance your avionics system was designed to deliver.

Cart

Close

Your cart is currently empty.

Start Shopping

Select options

Close